Browse New, Used, and Rebuilt Inventory in Stock
| Condition | Model | S/N | Description | Delivery |
|---|---|---|---|---|
| NEW | DPM-1QT Double Planetary Mixer Batch Change Can |
Air/Oil Reverse Hydraulic Lift, 1/2HP XP, Vac, SS-316 Flexi-Lip Sealed Gearbox and HV Blades, 150-Grit, 2-2" S&G Ports, Viton, Can-Hood Clamps, 50psig Vac Internally Machined Mix Can with Thermo, Bench w/level mounts. Can-Hood Clamps. Nema 12 Control Panel, 3/60/230v, 4" Color Touch Screen with start/stop, speed control, displays for speed, load, temp and cycle timer, speed and temperature calibration, E-Stop, Fused Rotary Disconnect. | 8-10 WEEKS | |
| NEW | DPM-2 Double Planetary Mixer Batch Change Can |
1.5HP, XP 3/60/230 volt, inverter-drive, T316, 80-grit, vacuum, HV Blades, Tefloflex, Sealed Flexi-Lip Gearbox, 2-3" ports, hood-can clamps, 100 psig ss jacket, Int-Mach, Thermo, 1" Ball Valve, Casters, Air/Oil Lift w/two-hand controls, Nema 12 Control Panel, 3/60/230v, 4" Color Touch Screen with Speed, Load, Time & Temp Displays, E-Stop, Disconnect, mounted and wired, Bench w/leveling pads. | 8-10 WEEKS | |
| NEW | DPM-4 Double Planetary Mixer Batch Change Can |
213724 | 2HP, XP 3/60/230 volt, inverter-drive, T316, 80-grit, vacuum, HV Blades, Viton, Sealed Flexi-Lip Gearbox, 2-3" ports, hood-can clamps, 50 psig ss jacket, Thermo, 1"TC Ball Valve, Caster, Air/Oil Lift w/two-hand controls, Nema 12 Control Panel, 3/60/230v, 4" Color Touch Screen with Speed, Load, Time & Temp Displays, E-Stop, Disconnect, mounted and wired, Bench w/leveling pads. | STOCK |
| RECON | DPM-1QT Double Planetary Mixer Batch Change Can |
213723 | Air/Oil Reverse Hydraulic Lift, 1/2HP XP, Vac, SS-316 Flexi-Lip Sealed Gearbox and HV Blades, Side/Bottom Scrapers, 150-Grit, 2-2" S&G Ports, Viton, Can-Hood Clamps, 50psig Vac Internally Machined Mix Can with Casters and Thermo. Bench w/casters. Can-Hood Clamps. Nema 12 Control Panel, 3/60/230v, 4" Color Touch Screen with start/stop, speed control, displays for speed, load, temp and cycle timer, speed and temperature calibration, E-Stop, Fused Rotary Disconnect. Vacuum Pump, 3/4HP, 3/60/230v installed on lower bench, plumbed with filter and valves, starter in panel. | STOCK |
| RECON | DPM-1QT Double Planetary Mixer Batch Change Can |
104335 | Air/Oil Reverse Hydraulic Lift, 1/2HP XP, Vac, SS-316 Gearbox and HV Blades, 150-Grit, 2-2" S&G Ports, Viton, Can-Hood Clamps, Mix Can with 30psig Jacket (No Valve). Nema 12 Control Panel, VFD w/Keypad, Estop & Disconnect, 3/60/230v. Vacuum Pump w/On/Off/Starter. Bench w/Casters. (Rect Blades $2205) | 1-WEEK |
| RECON | DPM-1QT Double Planetary Mixer Batch Change Can |
213810 | Air/Oil Reverse Hydraulic Lift, 1/2HP XP, Vac, SS-316 Gearbox and Rect Blades, 150-Grit, 2-2" S&G Ports, Viton, Can-Hood Clamps, Mix Can, Vac with 1/2" Ball Valve. Nema 7/9 XP Control Panel, Start/Stop/Pot/Estop, Color Screen with displays for speed and load, VFD mounted in XP panel, 1/60/115v Input, 3/60/230v Output. | STOCK |
| RECON | DPM-1 Double Planetary Mixer Batch Change Can |
103846 | 1HP, TEFC 3/60/230 volt, inverter-drive, T316, 80-grit, vacuum, HV Blades, Viton, Sealed Flexi-Lip Gearbox, 2-3" ports, hood-can clamps, 50psig ss jacket, Casters. Stainles Steel Base. Air/Oil Lift w/two-hand controls, Nema 12 Control Panel, 3/60/230v, KEYPAD CONTROL with Speed, Load Displays, E-Stop, Disconnect, mounted and wired, Stainless Steel Bench w/leveling pads. Transfer Cart for 1-gallon, carbon steel, painted with casters. | 3-4 weeks. |
| RECON | DPM-4 Double Planetary Mixer Batch Change Can |
105389 | 2HP, XP 3/60/230 volt, inverter-drive, T316, 80-grit, vacuum, HV Blades, Viton, Sealed Flexi-Lip Gearbox, 2-3" ports, hood-can clamps, Mix Can, Non-Jacketed, 1"TC Ball Valve, Casters, Air/Oil Lift w/two-hand controls, Nema 12 Control Panel 3/60/230, Color Touch Screen with Timer, VFD, E-Stop, Disconnect, mounted and wired. BENCH w/Level Mounts. | 1-2 WEEKS |
| RECON | DPM-4 Double Planetary Mixer Batch Change Can |
111647 | 2HP, XP 3/60/230 volt, inverter-drive, T316, 80-grit, Vacuum Hood & Rect Blades. Viton, Sealed Flexi-Lip Gearbox (T316), 2-3" ports, hood-can clamps, Mix Can, T304, 80-grit, Non-Jacketed, 1" NPT Ball Valve, Casters, Air/Oil Lift w/two-hand controls. Stainless Steel Base (bench top) with cutout for ball valve outlet. Nema 7/9 XP Control Panel 3/60/460v, Speed Display, Start/Stop/Pot, VFD, E-Stop,mounted and wired. BENCH w/level mounts. | 2-3 WEEKS |
| RECON | LDM-1QT Double Planetary Mixer Batch Change Can |
55122 | Air/Oil Reverse Manual Lift, 1/2HP XP, Vac, SS-316 Gearbox and Rect Blades, 80-Grit, 2-2" S&G Ports, Viton, Mix Can w/15psi SS jacket. | 2-3 weeks |
| NEW | DPM-40 Double Planetary Mixer Batch Change Can |
Air/Oil Hydraulic Lift, 15HP TEFC Mechanical Vari-drive, Vacuum, T316 80-grit Int, Blast Ext, HV Stirrer blades, two-3" TC S&C ports, one 1"NPT port, Viton, Sealed Cast Iron Gearbox (painted), Can-Hood Clamps, T316, Mix Can, Vacuum, DS-Rated, 80-grit, 25 psig SS jacket, RTD Thermo, 2" FBBV, Casters. Controls to be added (will add 2-4+ weeks to lead time). | TBD | |
| RECON | HDM-4S Double Planetary Mixer Batch Change Can |
77595 | 3HP, XP 3/60/230 volt, VFD Direct-Drive, all stainless steel exterior, 35psi @ 295f Internal Pressure, T316, 150-grit, Vacuum Hood w/100psi Jacket, ASME Code Stamped Vacuum Hood, 1-3" CB Sight Port, 3-3" TC ports, 2-2" TC ports, two 1/2" npt ports. HD Rect Blades with greater than normal clearance, Viton, Sealed Flexi-Lip Gearbox (T316) and Double FlexiLip Seals on Main Shaft. ASME J-Clamps (hood-can). Mix Can, T316, 150-grit, ASME 125psi @ 295f SS Jacket, 1" ITT Pureflow Diaphragm Valve on-center with 1" TC outlet (manual), KYNAR COATING. BENCH, stainless steel w/casters. (NO CONTROLS) | 4-6 WEEKS |
| RECON | DPM-10 Double Planetary Mixer Batch Change Can |
101354 | Air/oil hydraulic lift, 3HP XP VFD direct drive, Vacuum, T316-Vacuum Hood, 80-grit Int/Ext, T316-HV Stirrer blades, Side/Bottom Scrapers, two-3" S&C ports, one 1"NPT port, FlewxiLip Seals, Viton, Cast Iron Gearbox (painted), Side-wall Scraper. Mix Can, Vacuum, DS-Rated, 80-grit, 50psig CS jacket, 2" FBBV, Casters. (15HP 3/60/460v VFD, XP S/S/P/E Op Station - $3220) | 1-WEEK |
| RECON | HDM-40 Double Planetary Mixer Batch Change Can |
76170 | Reverse Lift, motorized hydraulic lift (1.5HP XP), 15HP XP Direct-Drive, Vacuum, T316, Vacuum Hood, 80-grit Int/Ext, Rect Stirrer blades, two-3" S&C ports, one 1"NPT port, Viton, Cast Iron Gearbox (painted). Prox Sensor (height) and XP L/S for Mix Can. T316-Mix Can, Vacuum, 80-grit, 50psig SS jacket, Casters, Trunions, NO OUTLET. | 6-8 WEEKS |
| RECON | HDM-40 Double Planetary Mixer Batch Change Can |
76580 | Reverse Lift, motorized hydraulic lift (1.5HP XP), 15HP XP Direct-Drive, Vacuum, T316, Vacuum Hood, 80-grit Int/Ext, Rect Stirrer blades, two-3" S&C ports, one 1"NPT port, Viton, Cast Iron Gearbox (painted). Prox Sensor (height) and XP L/S for Mix Can. T316-Mix Can, Vacuum, 80-grit, 50psig SS jacket, Casters, Trunions, NO OUTLET. | 6-8 WEEKS |
| RECON | DPM-40 Double Planetary Mixer Batch Change Can |
100890 | Reverse Lift, motorized hydraulic lift (1.5HP XP), 15HP XP Direct-Drive, Vacuum, T316, Vacuum Hood, 80-grit Int/Ext, Rect Stirrer blades, two-3" S&C ports, one 1"NPT port, Viton, Cast Iron Gearbox (painted). Prox Sensor (height) and XP L/S for Mix Can. T316-Mix Can, Vacuum, 80-grit, 50psig SS jacket, Casters, Trunions, NO OUTLET. | 6-8 WEEKS |
| RECON | DPM-40 Double Planetary Mixer Batch Change Can |
101831 | Reverse Lift, motorized hydraulic lift (1.5HP XP), 15HP XP Direct-Drive, Vacuum, T316, Vacuum Hood, 80-grit Int/Ext, Rect Stirrer blades, two-3" S&C ports, one 1"NPT port, Viton, Cast Iron Gearbox (painted). Prox Sensor (height) and XP L/S for Mix Can. T316-Mix Can, Vacuum, 80-grit, 50psig SS jacket, Casters, Trunions, NO OUTLET. | 6-8 WEEKS |
| RECON | DPM-40 Double Planetary Mixer Batch Change Can |
102962 | Reverse Lift, motorized hydraulic lift (1.5HP XP), 15HP XP Direct-Drive, Vacuum, T316, Vacuum Hood, 80-grit Int/Ext, Rect Stirrer blades, two-3" S&C ports, one 1"NPT port, Viton, Cast Iron Gearbox (painted). Prox Sensor (height) and XP L/S for Mix Can. T316-Mix Can, Vacuum, 80-grit, 50psig SS jacket, Casters, Trunions, NO OUTLET. | 6-8 WEEKS |
| RECON | DPM-40 Double Planetary Mixer Batch Change Can |
102963 | Reverse Lift, motorized hydraulic lift (1.5HP XP), 15HP XP Direct-Drive, Vacuum, T316, Vacuum Hood, 80-grit Int/Ext, Rect Stirrer blades, two-3" S&C ports, one 1"NPT port, Viton, Cast Iron Gearbox (painted). Prox Sensor (height) and XP L/S for Mix Can. T316-Mix Can, Vacuum, 80-grit, 50psig SS jacket, Casters, Trunions, NO OUTLET. | 6-8 WEEKS |
| RECON | DPM-40 Double Planetary Mixer Batch Change Can |
106198 | Reverse Lift, motorized hydraulic lift (1.5HP XP), 15HP XP Direct-Drive, Vacuum, T316, Vacuum Hood, 80-grit Int/Ext, Rect Stirrer blades, two-3" S&C ports, one 1"NPT port, Viton, Cast Iron Gearbox (painted). Prox Sensor (height) and XP L/S for Mix Can. T316-Mix Can, Vacuum, 80-grit, 50psig SS jacket, Casters, Trunions, NO OUTLET. | 6-8 WEEKS |
| RECON | HDM-75 Double Planetary Mixer Batch Change Can |
109830 | Reverse Lift, motorized hydraulic lift (2HP XP), 30HP XP VFD Drive (40-amps), Vacuum, T316, 80-grit Int/Ext, Rectangular Blades, Vacuum Hood with two-3" Sight & Charge (CB) ports, one 1"NPT port, Cast Iron Gearbox (painted), T316-Mix Can, Vacuum, 80-grit, 50psig SS jacket, Trunions, Casters, Fork Channels, NO OUTLET. | 8-10 WEEKS |
| NEW | PDM-40 Power Mix Planetary Disperser Planetary Mixer Batch Change Can |
**** | Air/Oil lift, Vacuum, SS-316, Viton, 80 grit, STD Carbon Steel Gearbox w/caps and Viton gaskets, 7.5HP XP Stirrer, 15HP XP Disperser, 1 - 1" NPT plus 2-3" S&G ports, Mix Can, 2" FBBV, Casters, 50psig SS jacket, RTD thermo. Controls to be added (will add 2-4+ weeks to lead time). | TBD |
| RECON | PDM-1/2 Power Mix Planetary Disperser Planetary Mixer Batch Change Can |
215396 | Air/oil Reverse Lift, SS-304, Vac, 80grit, Silicone, SS sealed gearbox (FlexiLip), 2-2" CB ports, one (1) 1/2" NPT port, 1/4" NPT port w/Vac Trans. 1/2HP TEFC planetary, 1 HP TEFC disperser w/2" HSD Blade, Mix Can, 50psig SS Jacket. Nema-12 Control Panel 3/60/230v, 7" Touch Screen with on/off's and displays, timer, vac pump on/off/starter, Vac/Pres display, VFD's, E-stop, Disconnect, Plug w/20' cord. Vacuum Pump with valves and filter, plumbed/wired. Bench w/casters. | 1 WEEK |
| RECON | PD-40 Power Mix Planetary Disperser Planetary Mixer Batch Change Can |
68781 | Air/Oil lift, Vacuum, SS-304, Viton, 80 grit-Int/ext, Cast Iron Gearbox (open belt/bearing design) w/Dust Shield, 7.5HP XP Stirrer, 10HP XP Disperser, Sidewall Scraper, Rectangular Stirrer Blade, 3 - 4" S&G port, 1 -1-1/2" port, 1-1" port. Mix Can, 50psig CS jacket, 3" TC Outlet flush bottom off-center with plug, fork channels, Casters (#200569CAN). VFD'S 7.5 & 10HP 230V, XP OP STATION TWO (2) S/S/POT, E-STOP, TEMP METER. | 3-4 WEEKS |
| NEW | VMC-2 Versa Mix Multi Shaft Mixer Anchor Agitator Change Can Batch Homogenizer |
* | Air/Oil Reverse Hydraulic Lift, Vac & 8psi Int, SS316, 150grit int, 80-grit ext, Viton, two-2" S&G & one 1/2" NPT, Thermoprobe/well 1/2 HP XP 3-Wing Anchor, Fixed Scrapers, Dry Running Double FlexiLip FDA MF Teflon shaft seals, can-cover clamps, 1 HP XP M/E, 1 HP XP Disp, 10:1 speed ranges. 50psig, 1" BV w/TC outlet, Int Mach, casters. Bench w/level mounts. NO CONTROLS | 8-10 WEEKS |
| NEW | VMC-10 Versa Mix Multi Shaft Mixer Anchor Agitator Change Can Batch Homogenizer |
* | SS-316, 150-grit int, 80-grit ext, Vacuum, XP Motors, 2-3" S&G ports, 1-1" NPT port, RTD Thermowell, Viton, 50 psig CS jacket, 2" FBBV, Casters, 80 grit, 3HP anchor w/scrapers, 5HP ME/SLIM bushingless w/Large Sq Hole Stator, 5HP disperser w/4-1/2" blade. | 8-10 WEEKS |
| NEW | VMC-40 Versa Mix Multi Shaft Mixer Anchor Agitator Change Can Batch Homogenizer |
115392 | SS-316, 80-grit int, 80-grit ext, Vacuum, Mechanical Seals, Teflon/TES/Kalrez, XP Motors, 2-3" S&G ports, 2-1-1/2" TC ports, RTD Thermowell, 4-Clamps, 50 psig SS jacket, 2" FBBV-TC, Casters, 80 grit, 5HP anchor w/scrapers, 5HP ME/SLIM bushingless w/Large Sq Hole Stator, 7.5HP disperser w/6" blade. | 4-5 WEEKS |
| NEW | CDA-50 Dual Shaft Mixer Anchor Agitator Batch Change Can Paint Mixer |
* | SS-304/80, Vac, change-can, air/oil hyd lift, ss vac cover w/1" FNPT, 2-3" S&G ports, 50 psig cs jckt, 2" Ball Valve, Casters, FlexiLip seals, Viton, 7" Disp blade w/10HP TEFC motor, 2-Wing Anchor w/5HP TEFC motor, 3/60/230/460v. (TA) Select required controls. UPGRADE TO T316/150-GRIT AVAILABLE. | STOCK |
| NEW | CDA-100 Dual Shaft Mixer Anchor Agitator Batch Change Can Paint Mixer |
* | SS-304/80, Vac, change-can, air/oil hyd lift, ss vac cover w/1" FNPT, 2-3" S&G ports, 50 psig cs jckt, 2" Ball Valve w/6" clearance, Casters, FlexiLip seals, Viton, 8" Disp blade w/15HP TEFC motor, 2-Wing Anchor w/10HP TEFC motor, 3/60/230/460v. Select required controls. UPGRADE TO T316/150-GRIT AVAILABLE. | STOCK |
| NEW | CDA-200 Dual Shaft Mixer Anchor Agitator Batch Change Can Paint Mixer |
* | SS-304/80, Vac, change-can, air/oil hyd lift, ss vac cover w/1" FNPT, 2-3" S&G ports, 50 psig cs jckt (1.5"NPT ports), 2" Ball Valve (NPT) w/6" clearance, Casters, 80 grit int, FlexiLip seals, Viton, 12" Disp blade w/20HP TEFC motor, 2-Wing Anchor w/10HP TEFC motor, 3/60/230/460v. Select required controls. UPGRADE TO T316/150-GRIT AVAILABLE. | STOCK |
| RECON | CDA-150 Dual Shaft Mixer Anchor Agitator Batch Change Can Paint Mixer |
70635 | SS-304, Vac, Viton, change-can, DUAL POST air/oil hyd lift on free standing floor base, Vac cover w/Two 1" FNPT ports, two 3" S&G ports, One 6" 150# ANSI loading port, two (2) 2" 150# ANSI ports, one 1-1/2" NPT port, Double Flexi Dry Running shaft seals (Retrofit), Mix Can, Dished Bottom, 15psig @ 300f CS Jacket on side walls only, 2" 150# ANSI at 16" off floor, Casters, Mill Finish, 11" Disp blade w/15HP XP motor direct drive at 1750rpm, 2-Wing Anchor and 10HP XP motor at 45rppm, 3/60/230/460v. No Controls. 1999 | 4-5 WEEKS |
| NEW | TANK, 200-GAL Pressure Vessel Storage Tank |
102482-A | 200-gallon working, 250-gal full, mixing vessel. T316L, 240-grit Int, 180-grit Ext. 40" OD X 40.25" St Side rated for 13psig internal pressure at 212f. Removable dished cover (clamps). ASME 100psig/350f Jacket on sides only. Insulated (2") side/bottom sheathed in stainless steel T304 (welded). 2" MCF Ball Valve w/actuator, bottom center at 5.75" off floor, legs designed for addition of load cells. Two (2) Thermowells, bottom and sidewall. 18" Manway, two (2) 1-1/2"TC port w/Gama Jet VI spray machines, 25gpm@45psi 360-degree, 3" TC w/XP Fibre Optic Light, 3" TC sight glass/port, 2" TC, foru (4) 1" TC, lifting lugs. #D5557 | STOCK |
| NEW | TANK, 200-GAL Pressure Vessel Storage Tank |
102482-B | 200-gallon working, 250-gal full, mixing vessel. T316L, 240-grit Int, 180-grit Ext. 40" OD X 40.25" St Side rated for 13psig internal pressure at 212f. Removable dished cover (clamps). ASME 100psig/350f Jacket on sides only. Insulated (2") side/bottom sheathed in stainless steel T304 (welded). 2" MCF Ball Valve w/actuator, bottom center at 5.75" off floor, legs designed for addition of load cells. Two (2) Thermowells, bottom and sidewall. 18" Manway, two (2) 1-1/2"TC port w/Gama Jet VI spray machines, 25gpm@45psi 360-degree, 3" TC w/XP Fibre Optic Light, 3" TC sight glass/port, 2" TC, foru (4) 1" TC, lifting lugs. #D5557 | STOCK |
| NEW | TANK, 300-GALLON Pressure Vessel Storage Tank |
SF-747C | ASME Code, Horizontal Vessel, 300-Gallon, SN# SF-747C, with two saddles, 41" OD x 60" straight wall, rated for 500psig at 302 °s f, SS-316, (2) 4" 300# RFSO, (1) 6" 300# RFSO, (1) 2" 300# RFSO, (1) 2" FNPT, (2) 1" 300# FNPT, (2) 3/4" 3000# FNPT. | STOCK |
| RECON | DS-1QT-SS Discharge System Press |
72571 | DS-1QT-SS, 110psig under platen. Extended height. All Stainles Steel construction, bench and DS bridge sheathed in SS. T304, Viton, 1/2HP TEFC, 1/60/115/230 volt, Nema 4X on/off/starter with Raise/Lower Selector Switch and E-Stop. Foot Pedal controls. Stainless Steel Benchw/leveling pads. Pressure Chart. | 2-WEEKS |
| RECON | DS-1 Discharge System Press |
69370 | DS-2 Standard, 90psig under the platen, Three (3) auto-vents on platen, SS-316, 80-grit finish, Viton, TEFC, 1Ph, 60Hz, 115 volt. With bench, level mounts and Nema 12 on/off starter with raise/lower switch. | 1-2 weeks |
| RECON | CDS-2 Discharge System Press |
55608 | CDS-2, Old "C" frame design with Double Orings, 65psig under the platen, 1" MNPT Vent on platen w/plug, SS-304, 80-grit finish, Viton, TEFC, 3Ph, 60Hz, 230 volt. Nema 12 on/off starter, 1/2hp 3/60/230V. Cast Base with cut out for ball valve. CAN NOT BE USED WITH CASTERS ON MIX CAN. No bench. | 3-WEEKS |
| RECON | DS-2 Discharge System Press |
71249B | DS-2 Special design. 1/60/208v, 1/2HP TEFC. 200psig under platen. T304. Viton. Quick Disconnect platen. For use with standard 2-gallon mix cans (thicker platen for use with up to 1-1/4" cove plug). Platen has three air vent/release valves for automatic venting. Bench w/leveling pads. Nema 12 panel, disconnect, start (ILLUM). stop, starter for hyd pump, raise/off/lower, safety PB, e-stop, directional control valve, limit switch to prevent operation with can removed. | 2-3 WEEKS |
| RECON | DS-4 Discharge System Press |
100250 | DS-4 Special design for special 4-gal 11" ID cans. Matched for use with LDM-4 #76405. 1/60/208v, 1/2HP TEFC. 200psig under platen. T304. Viton. Quick Disconnect platen. Safety enclosure made from 1/2" thick Lexan. For use with standard 1-gallon mix cans (thicker platen for use with up to 1-1/4" cove plug). Platen has three air vent/release valves for automatic venting. Bench w/leveling pads. Nema 12 panel, disconnect, start (ILLUM). stop, starter for hyd pump, raise/off/lower, safety PB, e-stop, directional control valve, limit swithces to prevent operation with door open and/or can removed. | 2-3 WEEKS |
| RECON | DS-4 Discharge System Press |
74615 | DS-4, ALL STAINLESS STEEL w/sheathing, 3/60/230v, 1/2HP TEFC. 30psig under platen. T316, Viton, 1" TC port, special 7/8" port (RC0988). Pump with oil cooler for continuous use. Extnded height. Bench w/casters. Nema-4X 3/60/230v panel, disconnect, start/stop, starter for hyd pump, raise/off/lower with foot pedal, e-stop, directional control valve. (Ref 72723) | 2-3 WEEKS |
| RECON | DS-10 Discharge System Press |
110168 | Standard, SS-304 80-grit, 50psig, Viton, raised base (20" under valve), 3/4HP XP, Nema 12 On/Off/Starter 3/60/230v. (Transferred from NY-Lab 1/31/19) | STOCK |
| NEW | TRM 2.5 X 5 Three Roll Mill |
114821 | 2.5 X 5 Three Roll Mill, 1/2HP XP motor, bench/table top model, XP safety trip switch. Stainless Steel 440c precision ground rolls, cored for water cooling/heating. Adjustable SS Apron, Teflon End plates. Nip Block. Add controls, bench and/or other options. | 6-8 WEEKS |
| NEW | TRM 2.5 X 5 Three Roll Mill |
114822 | 2.5 X 5 Three Roll Mill, 1/2HP XP motor, bench/table top model, XP safety trip switch. Stainless Steel 440c precision ground rolls, cored for water cooling/heating. Adjustable SS Apron, Teflon End plates. Nip Block. Add controls, bench and/or other options. | 6-8 WEEKS |
| NEW | TRM 4 X 8 Three Roll Mill |
* | XP motor, floor model, Stainless Steel Rolls, Nema 12 start/stop/starter. | 6-8 WEEKS |
| NEW | TRM 5 X 12 Three Roll Mill |
* | XP motor, standard spec's per price sheets. | STOCK |
| RECON | TRM 4 X 8 Three Roll Mill |
69745 | Ross, 4X8 TRM, 2HP XP motor, floor model, water cooled CS 52100 rolls, hand wheel roll adjustments, bronze end guides, take off apron. KENT #19027 | 1-WEEK |
| RECON | KE-15 Kneader Extruder |
38794 | KE-15 CLASS-V, SS-304, 15HP Sigma Blades (Cored), 5HP Extrusion Screw (Cored), 42psig CS Jacket, N12 controls (single speed sigma, variable speed screw) 460V.S/N C11472 | STOCK |
| RECON | V-10 Vertical Cone Screw Blender Vacuum Dryer Dry Blender Vertical Blender |
72153 | Vacuum/20psig/350f, SS-304 wetted parts, Viton, dished head, 16" Hinged Manway, one (1) 4" 150# and one (1) 2" 150# ports, 100psig/350f ASME STAMPED dimpled jacket w/ 1-1/2" flanged 150# ports, dry mech seal & Teflon packing, 3" NPT manual outlet valve, 150 grit finish, 5HP XP screw, 1HP XP arm. | 2-WEEKS |
| NEW | 42N-1 Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender |
* | 3/4 hp, TEFC motor, SS-304, atmospheric, center discharge, 36" off floor, Teflon Braided Square Packing, Silicone Gasket, 60-grit Ext, 60-grit Interior, c/s painted, 230/460 volt, 3 phase, 60 Hz. (High HP Capable) - 2" DUST TIGHT KNIFE GATE VALVE. | (6) APRIL '20 |
| NEW | 42N-1S Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender |
* | 3/4 hp, TEFC motor, SS-316, Sanitary Design, atmospheric, center discharge, 36" off floor, Teflon Braided Square Packing, Silicone Gasket, 150-grit Ext, 150-grit Interior, c/s painted, 230/460 volt, 3 phase, 60 Hz. (High HP Capable) - 2" DUST TIGHT KNIFE GATE VALVE. | STOCK |
| NEW | 42N-5 Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender |
* | 3 HP, TEFC motor, SS-304, atmospheric, center discharge 36" off floor on legs, Single Cover with Safety Limit Switch, Teflon Braided Square Packing, Stainless Steel Split Stuffing Boxes, 1-pc Cover, Silicone Cover Gasket, Shaft Guards, all SS 60-grit finish, c/s painted, 230/460 volt, 3 phase, 60 Hz. - 3" DUST TIGHT KNIFE GATE VALVE. | STOCK |
| NEW | 42N-5S Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender |
* | 3 HP, TEFC motor, SS-316, Sanitary Design, Atmospheric, center discharge 36" off floor on legs, Single Cover with Safety Limit Switch, Teflon Braided Square Packing, SS-316 Stainless Steel Split Stuffing Boxes, Silicone Cover Gasket, Shaft Guards, all SS 150-grit finish, c/s painted, 230/460 volt, 3 phase, 60 Hz. - 3" DUST TIGHT KNIFE GATE VALVE. | STOCK |
| NEW | 42N-5SS Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender |
* | 3 HP, TEFC motor, SS-316, (New) Sanitary Design, Atmospheric, ALL STAINLESS STEEL, center discharge 36" off floor on legs, Safety Limit Switch, Teflon Braided Square Packing, SS-316 Split Stuffing Boxes, neoprene cover gasket, Shaft Guards, all SS 150-grit finish, c/s painted, 230/460 volt, 3 phase, 60 Hz. (High HP Capable) (ADD ALL SS VALVE AS REQUIRED). | STOCK |
| NEW | 42N-5SS Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender |
* | 3 HP, TEFC motor, SS-316, (New) Sanitary Design, Atmospheric, ALL STAINLESS STEEL, center discharge 36" off floor on legs, Safety Limit Switch, Teflon Braided Square Packing, SS-316 Split Stuffing Boxes, 1-pc Cover, Silicone Cover Gaskett, Shaft Guards, all SS 150-grit finish, c/s painted, 230/460 volt, 3 phase, 60 Hz.(ADD VALVE AS REQUIRED). | STOCK |
| NEW | 42N-5SS Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender |
* | 3 HP, TEFC motor, SS-316, (New) Sanitary Design, Atmospheric, ALL STAINLESS STEEL, center discharge 36" off floor on legs, Safety Limit Switch, Teflon Braided Square Packing, SS-316 Stainless Steel Split Stuffing Boxes, 1-pc Cover, Silicone Cover Gasket, Shaft Guards, all SS 150-grit finish, c/s painted, 230/460 volt, 3 phase, 60 Hz. (3" DUST TIGHT KNIFE GATE VALVE W/MANUAL HANDWHEEL). | STOCK |
| NEW | 42N-10 Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender |
* | 5 HP, TEFC motor, SS-304, atmospheric, center discharge 36" off floor, Teflon Braided Square Packing, Stainless Steel Split Stuffing Boxes, 2-pc Cover, Silicone Cover Gasket, all SS 60-grit, 230/460 volt, 3 phase, 60 Hz. (4" DUST TIGHT KNIFE GATE VALVE W/MANUAL HANDWHEEL). | STOCK |
| NEW | 42N-10S Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender |
* | 5 HP, TEFC motor, SS-316, (New) Sanitary Design, Atmospheric, center discharge 36" off floor on legs, Safety Limit Switch, Teflon Braided Square Packing, SS-316 Stainless Steel Split Stuffing Boxes, 2-pc Cover, Silicone Cover Gasket, Shaft Guards, all SS 150-grit finish, c/s painted, 230/460 volt, 3 phase, 60 Hz. (ADD VALVE AS REQUIRED). | STOCK |
| NEW | 42N-10SS Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender |
* | 5 HP, TEFC motor, SS-316, (New) Sanitary Design, Atmospheric, ALL STAINLESS STEEL, center discharge 36" off floor on legs, Safety Limit Switch, Teflon Braided Square Packing, SS-316 Stainless Steel Split Stuffing Boxes, 2-pc Cover, Silicone Cover Gasket, Shaft Guards, all SS 150-grit finish, c/s painted, 230/460 volt, 3 phase, 60 Hz. (High HP Capable) (ADD VALVE AS REQUIRED). | STOCK |
| NEW | 42N-10SS Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender |
* | 5 HP, TEFC motor, SS-316, (New) Sanitary Design, Atmospheric, ALL STAINLESS STEEL, center discharge 36" off floor on legs, Safety Limit Switch, Teflon Braided Square Packing, SS-316 Stainless Steel Split Stuffing Boxes, 2-pc Cover, Silicone Cover Gasket, Shaft Guards, all SS 150-grit finish, c/s painted, 230/460 volt, 3 phase, 60 Hz. (High HP Capable) 4" DUST TIGHT KNIFE GATE VALVE | STOCK |
| NEW | 42N-18 Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender |
* | 7.5 HP, TEFC motor, SS-304, atmospheric, 36" off floor on legs, Safety Limit Switch, Teflon Braided Square Packing, Stainless Steel Split Stuffing Boxes, Silicone Cover Gasket, Shaft Guards, all SS 60-grit finish, c/s painted, 230/460 volt, 3 phase, 60 Hz. (High HP Capable) - 4" DUST TIGHT KNIFE GATE VALVE | (4/3) APRIL '20 |
| NEW | 42N-18S Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender |
* | 7.5 HP, TEFC motor, SS-316, Sanitary Design, 4" DUST TIGHT KNIFE GATE VALVE, Atmospheric, with center discharge 36" off floor on legs, Safety Limit Switch, Teflon Braided Square Packing, SS-316 Stainless Steel Split Stuffing Boxes, Silicone Cover Gasket, Shaft Guards, all SS 150-grit finish, c/s painted, 230/460 volt, 3 phase, 60 Hz. (High HP Capable). | STOCK |
| NEW | 42N-18SS Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender |
* | 7.5 HP, TEFC motor, SS-316, Sanitary Design, ALL STAINLESS STEEL, Atmospheric, with center discharge 36" off floor on legs, Safety Limit Switch, Teflon Braided Square Packing, , Shaft Guards, all SS 150-grit finish, c/s painted, 230/460 volt, 3 phase, 60 Hz. (High HP Capable) (ADD VALVE AS REQUIRED). | (3) AUG '20 |
| NEW | 42N-25 Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender |
* | 10 HP, TEFC motor, SS-304, atmospheric, 4" Dust Tight Knife Gate Valve Center Discharge 36" off floor on legs, Safety Limit Switch, Teflon Braided Square Packing, Stainless Steel Split Stuffing Boxes, Silicone Cover Gasket, Shaft Guards, all SS 80-grit finish, c/s painted, 230/460 volt, 3 phase, 60 Hz. (4" DUST TIGHT KNIFE GATE VALVE) | STOCK |
| NEW | 42N-25S Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender |
* | 10 HP, TEFC motor, SS-316, Sanitary Design, Atmospheric, center discharge 36" off floor on legs, Safety Limit Switch, Teflon Braided Square Packing, SS-316 Stainless Steel Split Stuffing Boxes, Silicone Cover Gasket, Shaft Guards, all SS 150-grit finish, c/s painted, 230/460 volt, 3 phase, 60 Hz. (4" DUST TIGHT KNIFE GATE VALVE) | STOCK |
| NEW | 42N-25SS Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender |
* | 10 HP, TEFC motor, SS-316, Sanitary Design, Atmospheric, ALL STAINLESS STEEL, center discharge 36" off floor on legs, Safety Limit Switch, Teflon Braided Square Packing, SS-316 Stainless Steel Split Stuffing Boxes, Silicone Cover Gasket, Shaft Guards, all SS 150-grit finish, c/s painted, 230/460 volt, 3 phase, 60 Hz. (ADD VALVE AS REQUIRED). | STOCK |
| NEW | 42N-25SS Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender |
* | 10 HP, TEFC motor, SS-316, Sanitary Design, Atmospheric, ALL STAINLESS STEEL, center discharge 36" off floor on legs, Safety Limit Switch, Teflon Braided Square Packing, SS-316 Stainless Steel Split Stuffing Boxes, Silicone Cover Gasket, Shaft Guards, all SS 150-grit finish, c/s painted, 230/460 volt, 3 phase, 60 Hz. (ADD VALVE AS REQUIRED). | STOCK |
| NEW | 42N-25SS Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender |
* | 10 HP, TEFC motor, SS-316, Sanitary Design, Atmospheric, ALL STAINLESS STEEL, center discharge 36" off floor on legs, Safety Limit Switch, Teflon Braided Square Packing, SS-316 Stainless Steel Split Stuffing Boxes, Silicone Cover Gasket, Shaft Guards, all SS 150-grit finish, c/s painted, 230/460 volt, 3 phase, 60 Hz. (4" DUST TIGHT KNIFE GATE VALVE) | STOCK |
| NEW | 42N-36 Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender |
* | 15 HP, TEFC motor, s/s 304, atmospheric, center discharge 36" off floor, Teflon Braided Square Packing, Stainless Steel Split Stuffing Boxes, Silicone Cover Gasket, all SS 60-grit, c/s painted, 230/460 volt, 3 phase, 60 Hz. (High HP Capable) with 6" DUST TIGHT KNIFE GATE VALVE. | STOCK |
| NEW | 42N-36 Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender |
* | 15 HP, TEFC motor, s/s 304, atmospheric, center discharge 36" off floor, Teflon Braided Square Packing, Stainless Steel Split Stuffing Boxes, Silicone Cover Gasket, all SS 60-grit, c/s painted, 230/460 volt, 3 phase, 60 Hz. (High HP Capable) with 6" DUST TIGHT KNIFE GATE VALVE. | STOCK |
| NEW | 42N-36S Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender |
* | 15 HP, TEFC motor, SS-316, Sanitary Design, Atmospheric, center discharge 36" off floor on legs, Safety Limit Switch, Teflon Braided Square Packing, SS-316 Stainless Steel Split Stuffing Boxes, Silicone Cover Gasket, Shaft Guards, all SS 150-grit finish, c/s painted, 230/460 volt, 3 phase, 60 Hz. with 6" DUST TIGHT KNIFE GATE VALVE. | STOCK |
| NEW | 42N-36SS Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender |
* | 15 HP, TEFC motor, SS-316, ALL STAINLESS STEEL, Sanitary Design, Atmospheric, center discharge 36" off floor on legs, Safety Limit Switch, Teflon Braided Square Packing, SS-316 Stainless Steel Split Stuffing Boxes, Silicone Cover Gasket, Shaft Guards, all SS 150-grit finish Int, 80-grit Ext, 230/460 volt, 3 phase, 60 Hz. (ADD VALVE AS REQUIRED). | STOCK |
| NEW | 42N-52 Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender |
* | 20 hp, TEFC motor, s/s 304, center discharge 36" clearance off floor, Stainless Steel Split Stuffing Boxes, Silicone Cover Gasket, all SS 80-grit, 230/460 volt, 3 phase, 60 Hz. 8" Dust Tight Knife Gate Valve. | STOCK |
| NEW | 42N-52S Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender |
* | 20 HP, TEFC motor, SS-316, Sanitary Design, Atmospheric, center discharge 36" off floor on legs, Safety Limit Switch, Teflon Braided Square Packing, SS-316 Split Stuffing Boxes, neoprene cover gasket, Shaft Guards, all SS 150-grit finish, c/s painted, 230/460 volt, 3 phase, 60 Hz. (High HP Capable) 8" Dust Tight Knife Gate Valve. | STOCK |
| NEW | 42B-1 Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender |
* | "B DESIGN" 1/2 HP, TEFC motor, SS-304, atmospheric, 99rpm, center discharge 36" off floor, Teflon Braided Square Packing, 1-pc cover w/Silicone Gasket, all SS 60-grit, 230/460 volt, 3 phase, 60 Hz. (Rated @ 35#/CF) 2" KNIFE GATE VALVE | STOCK |
| NEW | 42B-1 Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender |
* | "B DESIGN" 1/2 HP, TEFC motor, SS-304, atmospheric, 99rpm, center discharge 36" off floor, Teflon Braided Square Packing, 1-pc cover w/Silicone Gasket, all SS 60-grit, 230/460 volt, 3 phase, 60 Hz. (Rated @ 35#/CF) 2" KNIFE GATE VALVE | (8) AUG '20 |
| NEW | 42B-5 Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender |
* | "B DESIGN" 1-1/2 HP, TEFC motor, SS-304, atmospheric, 70rpm, center discharge 36" off floor, Teflon Braided Square Packing, 1-pc cover w/Silicone Gasket, all SS 60-grit, 230/460 volt, 3 phase, 60 Hz. (Rated @ 35#/CF) 3" KNIFE GATE VALVE | STOCK |
| NEW | 42B-5 Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender |
* | "B DESIGN" 1-1/2 HP, TEFC motor, SS-304, atmospheric, 70rpm, center discharge 36" off floor, Teflon Braided Square Packing, 1-pc cover w/Silicone Gasket, all SS 60-grit, 230/460 volt, 3 phase, 60 Hz. (Rated @ 35#/CF) 3" KNIFE GATE VALVE | STOCK |
| NEW | 42B-10 Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender |
* | "B DESIGN" 3 HP, TEFC motor, SS-304, atmospheric, 56rpm, center discharge 36" off floor, Teflon Braided Square Packing, 2-pc cover w/Silicone Gasket, all SS 60-grit, 230/460 volt, 3 phase, 60 Hz. (Rated @ 35#/CF) 4" KNIFE GATE VALVE | STOCK |
| NEW | 42B-10 Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender |
* | "B DESIGN" 3 HP, TEFC motor, SS-304, atmospheric, 56rpm, center discharge 36" off floor, Teflon Braided Square Packing, 2-pc cover w/Silicone Gasket, all SS 60-grit, 230/460 volt, 3 phase, 60 Hz. (Rated @ 35#/CF) 4" KNIFE GATE VALVE | (4) APRIL '20 |
| NEW | 42B-18 Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender |
* | "B DESIGN" 5 HP, TEFC motor, (Vertically Mounted Motor), SS-304, 45rpm, atmospheric, center discharge 36" off floor, Teflon Braided Square Packing, 2-pc cover w/Silicone Gasket, all SS 60-grit, 230/460 volt, 3 phase, 60 Hz. (Rated @ 35#/CF) 4" KNIFE GATE VALVE | STOCK |
| NEW | 42B-18 Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender |
* | "B DESIGN" 5 HP, TEFC motor, (Vertically Mounted Motor), SS-304, 45rpm, atmospheric, center discharge 36" off floor, Teflon Braided Square Packing, 2-pc cover w/Silicone Gasket, all SS 60-grit, 230/460 volt, 3 phase, 60 Hz. (Rated @ 35#/CF) 4" KNIFE GATE VALVE | (4) JUNE '20 |
| NEW | 42B-25 Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender |
* | "B DESIGN" 7.5 HP, TEFC motor, SS-304, 43rpm, atmospheric, center discharge 36" off floor, Teflon Braided Square Packing, 2-pc cover w/Silicone Gasket, all SS 60-grit, 230/460 volt, 3 phase, 60 Hz. (Rated @ 35#/CF) 4" KNIFE GATE VALVE | STOCK |
| NEW | 42B-36 Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender |
* | "B DESIGN" 10 HP, TEFC motor, SS-304, 40rpm, atmospheric, center discharge 36" off floor, Teflon Braided Square Packing, 2-pc cover w/Silicone Gasket, all SS 60-grit, 230/460 volt, 3 phase, 60 Hz. (Rated @ 35#/CF) 6" KNIFE GATE VALVE | STOCK |
| RECON | 42N-52S Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender |
215610 | 20 HP, TEFC motor, SS-316, Sanitary Design, Atmospheric, center discharge 36" off floor on legs, Safety Limit Switch, Teflon Braided Square Packing, SS-316 Split Stuffing Boxes, neoprene cover gasket, Shaft Guards, all SS 150-grit finish, c/s painted, 230/460 volt, 3 phase, 60 Hz. (High HP Capable) 8" Dust Tight Knife Gate Valve. Safety Grate with 1/2" holes covering 1/2 of the Trough. VFD, Nema 4X, 3/60/460v. | STOCK |
| RECON | CVD-007 Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender |
100757 | Cylindrical Vacuum Dryer, 7.5 cubic foot working, 9.6 cubic full holding, SS-304, 50psig @ 500F CS jacket, 3" roto-disc valve, thermo, 2 - 6" tri-clover port, 2 - 1"-150# couplings, Alum split stuffing boxes, 7.5HP XP INV Duty 10:1, 43rpm out, Paddle and Ribbon center discharge agitators, hollow shaft w/rotary union, 150-grit int, 2" fibreglass insulation, blast finish ext, Nema 4 VFD. (Filter Housing $21680) **** | STOCK |
| NEW | VCB-1 V Cone Blender Tumble Blender Dry Powder Blender |
114282 | 1CF/28.3-Liter, V-CONE BLENDER, 2HP TEFC, ATMOSPHERIC, SS-316, 150-GRIT FINISH INT, 80-GRIT EXT FINISH, 36RPM, INTENSIFIER BAR, PAINTED STEEL SUPPORT, 4" BUTTERFLY VALVE, 24" CLEARANCE UNDER VALVE, MECHANICAL SAFETY RAILING WITH LIMIT SWITCH, 3/60/230/460V, NEMA-12 CONTROL PANEL 3/60/230V, 2-VFD TOUCH-SCREEN, E-STOP, DISCONNECT. (150#/Cu.Ft.) | 2-WEEKS |
| NEW | VCB-1 V Cone Blender Tumble Blender Dry Powder Blender |
114849 | 1CF, V-CONE BLENDER, 2HP TEFC, ATMOSPHERIC, SS-316, 150-GRIT FINISH INT, 80-GRIT EXT FINISH, 36RPM, PAINTED STEEL SUPPORT, 4" BUTTERFLY VALVE, 24" CLEARANCE UNDER VALVE, MECHANICAL SAFETY RAILING WITH LIMIT SWITCH, 3/60/230/460V, NO CONTROLS. (150#/Cu.Ft.) | TBD |
| NEW | VCB-1 V Cone Blender Tumble Blender Dry Powder Blender |
114861 | 1CF, V-CONE BLENDER, 2HP TEFC, ATMOSPHERIC, SS-316, 150-GRIT FINISH INT, 80-GRIT EXT FINISH, 36RPM, 2HP INTENSIFIER BAR, PAINTED STEEL SUPPORT, 4" BUTTERFLY VALVE, 24" CLEARANCE UNDER VALVE, MECHANICAL SAFETY RAILING WITH LIMIT SWITCH, 3/60/230/460V, NO CONTROLS. (150#/Cu.Ft.) | STOCK |
| NEW | VCB-1 V Cone Blender Tumble Blender Dry Powder Blender |
114862 | 1CF, V-CONE BLENDER, 2HP TEFC, ATMOSPHERIC, SS-316, 150-GRIT FINISH INT, 80-GRIT EXT FINISH, 36RPM, 2HP INTENSIFIER BAR, PAINTED STEEL SUPPORT, 4" BUTTERFLY VALVE, 24" CLEARANCE UNDER VALVE, MECHANICAL SAFETY RAILING WITH LIMIT SWITCH, 3/60/230/460V, NO CONTROLS. (150#/Cu.Ft.) | STOCK |
| NEW | VCB-5 V Cone Blender Tumble Blender Dry Powder Blender |
114850 | 5CF, V-CONE BLENDER, 5HP TEFC, ATMOSPHERIC, SS-316, 150-GRIT FINISH INT, 80-GRIT EXT FINISH, 24RPM, PAINTED STEEL SUPPORT, 6" BUTTERFLY VALVE, 24" CLEARANCE UNDER VALVE, MECHANICAL SAFETY RAILING WITH LIMIT SWITCH, 3/60/230/460V, NO CONTROLS. (150#/Cu.Ft.) | 2-WEEKS |
| NEW | VCB-5 V Cone Blender Tumble Blender Dry Powder Blender |
114851 | 5CF, V-CONE BLENDER, 5HP TEFC, ATMOSPHERIC, SS-316, 150-GRIT FINISH INT, 80-GRIT EXT FINISH, 24RPM, PAINTED STEEL SUPPORT, 6" BUTTERFLY VALVE, 24" CLEARANCE UNDER VALVE, MECHANICAL SAFETY RAILING WITH LIMIT SWITCH, 3/60/230/460V, NO CONTROLS. (150#/Cu.Ft.) | 2-WEEKS |
| NEW | VCB-5 V Cone Blender Tumble Blender Dry Powder Blender |
114866 | 5CF, V-CONE BLENDER, 5HP TEFC, ATMOSPHERIC, SS-316, 150-GRIT FINISH INT, 80-GRIT EXT FINISH, 24RPM, 3HP INTENSIFIER BAR, PAINTED STEEL SUPPORT, 6" BUTTERFLY VALVE, 24" CLEARANCE UNDER VALVE, MECHANICAL SAFETY RAILING WITH LIMIT SWITCH, 3/60/230/460V, NO CONTROLS. (150#/Cu.Ft.) | STOCK |
| NEW | VCB-5 V Cone Blender Tumble Blender Dry Powder Blender |
114867 | 5CF, V-CONE BLENDER, 5HP TEFC, ATMOSPHERIC, SS-316, 150-GRIT FINISH INT, 80-GRIT EXT FINISH, 24RPM, 3HP INTENSIFIER BAR, PAINTED STEEL SUPPORT, 6" BUTTERFLY VALVE, 24" CLEARANCE UNDER VALVE, MECHANICAL SAFETY RAILING WITH LIMIT SWITCH, 3/60/230/460V, NO CONTROLS. (150#/Cu.Ft.) | STOCK |
| NEW | DCB-5 Double Cone Blender Tumble Blender Dry Powder Blender |
114868 | 5CF, DOUBLE CONE BLENDER, 5HP TEFC, ATMOSPHERIC, SS-316, 150-GRIT FINISH INT, 80-GRIT EXT FINISH, 20RPM, PAINTED STEEL SUPPORT, 6" BUTTERFLY VALVE, 24" CLEARANCE UNDER VALVE, MECHANICAL SAFETY RAILING WITH LIMIT SWITCH, 3/60/230/460V, NO CONTROLS. (150#/Cu.Ft.) | 2-WEEKS |
| RECON | DCB-10 V Cone Blender Tumble Blender Dry Powder Blender |
114384 | 10CF/283.2-Liter, DOUBLE CONE BLENDER, 7.5HP XP, ATMOSPHERIC, SS-304, 150-GRIT FINISH INT, 80-GRIT EXT FINISH, 20RPM, INTENSIFIER/SPRAY BAR AND 5HP XP MOTOR DRIVE WITH MAGNETIC SEALS, PAINTED STEEL SUPPORT, 8" BUTTERFLY VALVE, 36" CLEARANCE UNDER VALVE, MECHANICAL SAFETY RAILING WITH LIMIT SWITCH, 3/60/230V, NEMA 12 CONTROL PANEL TOUCH-SCREEN, E-STOP, DISCONNECT, NEMA 7/9 XP OPERATOR PANEL WITH START/STOP/POT/JOG/ESTOP. (125#/Cu.Ft.) | STOCK |
| NEW | HSM-100LSK-I Batch High Shear Mixer Rotor Stator Mixer Emulsifier Homogenizer Benchtop Lab |
HSM-100LSK-I with VFD design, 3/4HP, 1/60/115v 20amps, 500-10,000rpm, HSM. (Available options: HSD, Micro, In-Line, Quad, DT Prop, Various Stators, Bushings, HSD blades, Props, Beaker Clamp, Vessels.) | 1-2 DAYS | |
| NEW | HSM-100LCIT Batch High Shear Mixer Rotor Stator Mixer Emulsifier Homogenizer Benchtop Lab |
* | SS-316 Wetted Parts, 1HP Drive, Nema 12 IEC Motor, 115 volts, 1Ph, 50/60Hz, 20amps. (option for 1/50/60/190 or 230v). Variable Speed 500-10,000rpm (speed calibration to +/-1%), Constant Torque. TOUCH SCREEN CONTROL with Start/Stop, Speed, Time, Digital Display for Speed Display, Temperature Display (0-300F or 0-150C, RTD Temp Probe is an option), Batch Timer Display and Percent of Load Display, Calibration Screens for Temp and Speed. Raise/Lower Lift Push-Buttons, Calibration, Timer and other Function Controls. With SS-316 M/E Assembly, Disintegrating, Slotted & Fine Screen Heads, Teflon Bushing. Options: Disperser, Micro, Inline, Quad, Temp Probe and Beaker Clamp are available. | STOCK |
| NEW | HSM100LH-1 Batch High Shear Mixer Rotor Stator Mixer Emulsifier Homogenizer |
1HP High Shear Rotor/Stator Mixer, Air/Oil Hydraulic Lift, Table/Bench Mount Design, 1-3/8" Dia ME operating at 10,000rpm, Slotted Head, Teflon Bushing, SS-304, Shaft Guard, Limit Switches, Adj. Can Lock, Inverter Duty 10:1 TEFC Motor. OPTIONS: Other Stators and Bushings, VFD, Bench, Interchangeable Disperser and In-Line (Same as 400DL). In-line can be used with QUAD and Double Mechaincal Seals w/Barrier Tank. | 1 WEEK | |
| NEW | HSM100LH-2 Batch High Shear Mixer Rotor Stator Mixer Emulsifier Homogenizer |
2HP High Shear Rotor/Stator Mixer, Air/Oil Hydraulic Lift, Table/Bench Mount Design, 2" Dia ME operating at 6900rpm, Slotted Head, Teflon Bushing, SS-304, Shaft Guard, Limit Switches, Adj. Can Lock, Inverter Duty 10:1 TEFC Motor. OPTIONS: Other Stators and Bushings, VFD, Bench, Interchangeable Disperser and In-Line. In-line can be used with QUAD and Double Mechaincal Seals w/Barrier Tank. | 1 WEEK | |
| NEW | HSM100LH-2 Batch High Shear Mixer Rotor Stator Mixer Emulsifier Homogenizer |
2HP High Shear Rotor/Stator Mixer, AIR/OIL HYD LIFT, Table/Bench Mount Design, Disperseer Assemmbly with 3" Blade operating at 6900rpm, Shaft Guard, XP Limit Switches, Adj Can Lock, Inverter Duty 10:1 TEFC Motor, Nema 4X 208/230 VAC/3 PH 60HZVFD (loose). V-belt drive, start, stop spd control w/dig readout. VFD mounted & wired. | 1 WEEK | |
| NEW | HSM-101 Batch High Shear Mixer Rotor Stator Mixer Emulsifier Homogenizer |
Std per price sheets, T-316 wetted parts, XP, 50/60 Hz motors, slotted head, Teflon. | STOCK | |
| NEW | HSM-105 Batch High Shear Mixer Rotor Stator Mixer Emulsifier Homogenizer |
Std per price sheets, T-316 wetted parts, XP, 50/60 Hz motors, slotted head, Teflon. | STOCK | |
| NEW | HSM-110 Batch High Shear Mixer Rotor Stator Mixer Emulsifier Homogenizer |
Std per price sheets, T-316 wetted parts, XP, 50/60 Hz motors, slotted head, Teflon. | STOCK | |
| NEW | HSM400DLA Inline High Shear Mixer Rotor Stator Mixer Emulsifier Eductor Pump Homogenizer |
Basic Design. (Model 1), 1HP TEFC 3/60/230/460v VFD Capable Motor, Single Mech Seal 45psig, Viton, SS-316/80-grit, Slotted Head. Carbon Steel Painted. Add Bench, Controls, etc as required. | 1-2 WEEKS | |
| NEW | HSM400DLA Inline High Shear Mixer Rotor Stator Mixer Emulsifier Eductor Pump Homogenizer |
Enclosed Design, Carbon Steel Painted Base, Riser and Bench, 1HP TEFC VFD rated Motor 3/60/230/460v, 10,000rpm, Double Mechanical Seal (Kalrez) 250psig w/ Barrier Tank, Viton Orings, Slotted, Fine Screen & Disentigrating Stators, NPT Inlet and Outlet, 1HP Nema 12 VFD 3/60/230v. Leveling Pads. Mix Chamber Pressure Gauge, Inlet and Outlet Valves. Choose from many options on price sheet. | 1-2 WEEKS | |
| NEW | HSM-401 Inline High Shear Mixer Rotor Stator Mixer Emulsifier Eductor Pump Homogenizer |
1.5HP, Std Specs, slotted head, Chesterton 155, Viton, single seal. | STOCK | |
| NEW | HSM-405 Inline High Shear Mixer Rotor Stator Mixer Emulsifier Eductor Pump Homogenizer |
5HP, Std Specs, slotted head, Chesterton 155, Viton, single seal. | STOCK | |
| NEW | HSM-410 Inline High Shear Mixer Rotor Stator Mixer Emulsifier Eductor Pump Homogenizer |
10HP, Std Specs, slotted head, Chesterton 155, Viton, single seal. | STOCK | |
| RECON | HSM-100LCI-T Batch High Shear Mixer Rotor Stator Mixer Emulsifier Homogenizer Benchtop Lab |
210938 | TOUCH SCREEN CONTROL, 1HP Drive, 1/60/115v, 500-10,000rpm +/-1% w/calibration. Speed, Load, Temp, Timer displays, 15" lift, 16" under blade R/L push buttons. HSM, Data Aq. | STOCK |
| RECON | HSM-100LCI-T Batch High Shear Mixer Rotor Stator Mixer Emulsifier Homogenizer Benchtop Lab |
111534 | TOUCH SCREEN CONTROL, 1HP Drive, 1/60/115v, 500-10,000rpm +/-1% w/calibration. Speed, Load, Temp, Timer displays, 15" lift, 16" under blade R/L push buttons. HSM. | STOCK |
| RECON | HSM-105 Batch High Shear Mixer Rotor Stator Mixer Emulsifier Homogenizer |
215289 | SS-316 wetted parts, 5HP XP, slotted stator head, Glass Filled Teflon Bushing. | STOCK |
| RECON | HSM-110 Batch High Shear Mixer Rotor Stator Mixer Emulsifier Homogenizer |
215480 | T-316 wetted parts, 10HP XP, 50/60 Hz motors, SLIM w/Hose & Wand, T440C Large Square Stator, Stellite Tipped Rotor, Circulation Prop, Stellite Bushing/Sleeve. VFD 10HP 4X 3/60/230. Hanging Bracket. Mobile Lift. | STOCK |
| RECON | HSM-110 Batch High Shear Mixer Rotor Stator Mixer Emulsifier Homogenizer |
215152 | Std per price sheets, T-316 wetted parts, XP, 50/60 Hz motors, slotted head, Teflon. | STOCK |
| RECON | HSM-400DLA Inline High Shear Mixer Rotor stator Mixer Emulsifier Eductor Pump Homogenizer |
112673 | Std 400DLA. Single Mech Seal, CS Flat Base, Leveling Pads, 1HP TEFC VFD rated Motor 3/60/230/460v, 10,000rpm, Single Mechanical Seal 45psig w/Viton, Viton Chamber orings, SS-316, 80-grit, Slotted Stator, NPT Inlet (3/4") & Outlet (3/8"). | STOCK |
| RECON | HSM-400DLA Inline High Shear Mixer Rotor stator Mixer Emulsifier Eductor Pump Homogenizer |
212804 | Std 400DLA. Single Mech Seal, CS Flat Base, Leveling Pads, 1HP TEFC VFD rated Motor 3/60/230/460v, 10,000rpm, Single Mechanical Seal 125psig w/Viton, Viton Chamber orings, SS-316, 80-grit, Slotted & Fine Screen Stators, NPT Inlet (3/4") & Outlet (3/8"), Low Profile Thermo. Nema 4, 3/60/230v, 1HP VFD mounted & wired. | STOCK |
| RECON | HSM-400DLA Inline High Shear Mixer Rotor stator Mixer Emulsifier Eductor Pump Homogenizer |
213781 | Std 400DLA. Single Mech Seal, CS Flat Base, Leveling Pads, 1HP XP VFD rated Motor 3/60/230/460v, 10,000rpm, Single Mechanical Seal 125psig w/Kalrez, Kalrez Chamber orings, SS-316, 80-grit, Slotted Stator, NPT Inlet (3/4") & Outlet (3/8"), Nema 4X, 3/60/230v, 1HP VFD loose. | STOCK |
| RECON | HSM-401 Inline High Shear Mixer Rotor stator Mixer Emulsifier Eductor Pump Homogenizer |
214796 | XP, 1.5HP, 3/60/230/460V, slotted head, NPT, 130psig, Viton, single seal. | STOCK |
| RECON | HSM-405 Inline High Shear Mixer Rotor stator Mixer Emulsifier Eductor Pump Homogenizer |
215292 | XP, 5HP, 3600rpm, fine screen stator, Viton, Double Mech Seal (130psig) w/barrier tank, TC inlet/outlet. | STOCK |
| RECON | HSM-501 Vacuum Batch High Shear Mixer Rotor Stator Mixer Emulsifier Homogenizer |
66803 | slotted head, 1-1/2HP XP 230/460, 3/60Hz, bronze bushing, single or double mech seal. Hanging Bracket.**** | STOCK |
| RECON | HSM-510 Vacuum Batch High Shear Mixer Rotor Stator Mixer Emulsifier Homogenizer |
200224 | 10HP, slotted head, Bronze bushing, with single mechanical seal for vacuum application. **** | STOCK |
| RECON | PM-120 PreMax Ultra High Shear Batch Mixer Rotor Stator Homogenizer Batch |
208553 | 20HP XP, Standard Design, 3" Delta V Rotor/Stator, Air/Oil Hydraulic Lift, Floor Mounted Base Plate with matching 15-gal mix vessel w/jacket, cart, casters. | 1-Week |
| RECON | HSM-706X-30 Ultra High Shear Mixer Inline Mixer Rotor Stator Mixer Emulsifier Homogenizer X Series Quad Slot Mega Shear Colloid Mill |
214260 | 30HP XP, 6" dia X-5, 7200rpm, X-Series rotor/stator, T316/Viton/150-grit, 150psig @ 250f mix chamber, Double Mechanical Cartridge Seal w/barrier tank, Oil Pump for bearing system, 1-1/2" 150# inlet, 1-1/2" 150# outlet, CS base & enclosure. Three (3) gap shims .045", .060" & .075". Nema-4X, 30HP 480v VFD (loose). | STOCK |
| RECON | HSM-706MS-75 Ultra High Shear Mixer Inline Mixer Rotor Stator Mixer Emulsifier Homogenizer X Series Quad Slot Mega Shear Colloid Mill |
104225 | Sanitary Design, 75HP XP, 6" dia (7200rpm). MEGASHEAR rotor/stator, T316/Viton/150-grit, 150 psig mix chamber, Double Mechanical Seal w/barrier tank, Oil Pump for bearing system, 1-1/2" TC inlet, 1-1/2" TC outlet, stud & wingnut, SS base with fork channels. MEGA ONLY. ******** | 1 WEEK |
| RECON | ME-475XS-12 Ultra High Shear Mixer Inline Mixer Rotor Stator Mixer Emulsifier Homogenizer X Series Quad Slot Mega Shear Colloid Mill |
69907 | Sanitary Design, 75HP XP, 12" dia (3600rpm), direct drive (mod 6/19-CRS). X-4 rotor/stator, 150 psig mix chamber w/50psig SS Jacket, Single Mechanical Seal, Viton, 150 grit, 3" TC inlet, 2" TC outlet, Swing device for inlet plate with Voss Clamp, 1/2" TC drain, SS base with SS casters. | 1 WEEK |
| NEW | HSM-400SC-5 Inline High Shear Mixer Rotor Stator Mixer Emulsifier Eductor Pump Homogenizer SLIM |
Modified HSM-400 Lab Size Design, Sanitary, Horizontal, 5HP TEFC, double-mechanical seal and barrier tank, viton, SS-316, 80grit, 1" tri-clamp inlet & outlet with IN-LINE SLIM (I-SLIM) w/Hose & Wand, one-piece inlet/stator-slotted head. CS Flat Base, CS Tube Riser with Leveling Pads. Nema 1 VFD 3/60/230v, mounted and wired. Carbon Steel Painted Drive Base, Flat Base and Tube Riser. No drive enclosure. | 2-3 WEEKS | |
| NEW | HSM-405SC-25 Inline High Shear Mixer Rotor Stator Mixer Emulsifier Eductor Pump Homogenizer SLIM |
303956 | In-Line SLIM, Sanitary, Horizontal, 25HP XP, Viton O-ring for the mixing chamber, double-mechanical seal with silicon carbide seal faces vs. silicon carbide seal faces and Kalrez O-rings, and barrier tank, SS-316, 150grit, Wing Nuts, One 2" TC Inlet and one 2" tri-clamp outlet with IN-LINE SLIM (I-SLIM) 1-1/2" SLIM Port, w/hopper, one-piece inlet/stator-large square head. SS 2-cuft Hopper for powder loading, SS portable cart with casters. ADD CONTROLS. | 2-3 WEEKS |
| RECON | HSM-400SC-5 Inline High Shear Mixer Rotor Stator Mixer Emulsifier Eductor Pump Homogenizer SLIM |
210631 | Modified HSM-400 Lab Size Design, Sanitary, Horizontal, 5HP XP, double-mechanical seal and barrier tank, viton, SS-316, 150grit, 1" tri-clamp inlet & outlet with IN-LINE SLIM (I-SLIM), one-piece inlet/stator-large square head. Hose & Wand for powder loading. ALL STAINLESS STEEL ENCLOSURE, Base & Riser Panel mounted on SS casters. Nema-4 5HP 230v VFD. | STOCK |
| RECON | HSM-412SB-150 Inline High Shear Mixer Rotor Stator Mixer Emulsifier Eductor Pump Homogenizer SLIM |
67295 | Modified ME-450XS, 150HP TEFC Motor, double-mechanical seal and barrier tank, 9" Rotor/Stator viton, SS-316, 150grit, Voss tri-clamp, 4" tri-clamp inlet & 3" Tri-clamp outlet with IN-LINE SLIM (I-SLIM) 3" and 3" ball valve, hose & wand, slotted head. **** | STOCK |
| NEW | HSM100LH-1 Batch High shear Mixer Rotor Stator Mixer Emulsifier Homogenizer |
* | 1HP High Speed Disperser, Air/Oil Hydraulic Lift, Table/Bench Mount Design, 2" Disperser Blade operating at 10,000rpm, SS-304, Shaft Guard, Limit Switches, Adj. Can Lock, Inverter Duty 10:1 TEFC Motor. OPTIONS: VFD, Bench, Interchangeable ME (Same as LC) and In-Line (Same as 400DL). In-line can be used with QUAD and Double Mechaincal Seals w/Barrier Tank. | 1 WEEK |
| NEW | HSM100LH-2 Batch High shear Mixer Rotor Stator Mixer Emulsifier Homogenizer |
* | 2HP High Speed Disperser, Air/Oil Hydraulic Lift, Table/Bench Mount Design, 3.5" Disperser Blade operating at 5700rpm, SS-304, Shaft Guard, Limit Switches, Adj. Can Lock, Inverter Duty 10:1 TEFC Motor. OPTIONS: VFD, Bench, Interchangeable ME and In-Line. In-line can be used with QUAD and Double Mechaincal Seals w/Barrier Tank. | 1 WEEK |
| NEW | HSD-5 High Speed Disperser Batch |
* | 5hp High Speed Disperser, Lift Mounted on floor w/48" Rise, 6" Blade @ 8" off floor, SS-304, Shaft Guard, Limit Switches, Adj. Can Lock, TEFC Motor. (Add $510 for XP motor) | 1-2 WEEKS |
| NEW | HSD-7.5 High Speed Disperser Batch |
* | 7.5hp High Speed Disperser, Lift Mounted on floor w/48" Rise, 8" Blade @ 8" off floor, SS-304, Shaft Guard, Limit Switches, Adj. Can Lock, TEFC Motor. (Add $545 for XP motor) | 1-2 WEEKS |
| NEW | HSD-10 High Speed Disperser Batch |
* | 10hp High Speed Disperser, Lift Mounted on floor w/48" Rise, 10" Blade @ 8" off floor, SS-304, Shaft Guard, Limit Switches, Adj. Can Lock, TEFC Motor. (Add $645 for XP motor) | 1-2 WEEKS |
| NEW | HSD-15 High Speed Disperser Batch |
* | 15hp High Speed Disperser, Lift Mounted on floor w/48" Rise, 12" Blade @ 8" off floor, SS-304, Shaft Guard, Limit Switches, Adj. Can Lock, TEFC Motor. (Add $785 for XP motor) | 1-2 WEEKS |
| NEW | HSD-20 High Speed Disperser Batch |
* | 20hp High Speed Disperser, Lift Mounted on floor w/48" Rise, 14" Blade @ 8" off floor, SS-304, Shaft Guard, Limit Switches, Adj. Can Lock, TEFC Motor. (Add $895 for XP motor) | 1-2 WEEKS |
| NEW | HSD-25 High Speed Disperser Batch |
* | 25hp High Speed Disperser, Lift Mounted on floor w/54" Rise, 16" Blade @ 8" off floor, SS-304, Shaft Guard, Limit Switches, Adj. Can Lock, TEFC Motor. (Add $1050 for XP motor) | 1-2 WEEKS |
| NEW | HSD-30 High Speed Disperser Batch |
* | 30hp High Speed Disperser, Lift Mounted on floor w/54" Rise, 16" Blade @ 8" off floor, SS-304, Shaft Guard, Limit Switches, Adj. Can Lock, TEFC Motor. (Add $1110 for XP motor) | 1-2 WEEKS |
| NEW | HSD-50 High Speed Disperser Batch |
* | 50hp High Speed Disperser, Lift Mounted on floor w/66" Rise, 18" Blade @ 12" off floor, SS-304, Shaft Guard, Limit Switches, Adj. Can Lock, TEFC Motor. (Add $1450 for XP motor) | 1-2 WEEKS |
| RECON | HSD-10 High Speed Disperser Batch |
215001 | 10hp High Speed Disperser, Lift Mounted on floor w/48" Rise, 10" Blade @ 8" off floor, SS-304, Shaft Guard, Limit Switches, Adj. Can Lock, Inverter Duty TEFC Motor. | STOCK |
| RECON | HSD-15 High Speed Disperser Batch |
116024 | 15hp High Speed Disperser, Lift Mounted on floor w/48" Rise, 12" Blade @ 8" off floor, SS-304, Shaft Guard, Limit Switches, Adj. Can Lock, Inverter Duty XP Motor. | STOCK |
| RECON | HSD-20 High Speed Disperser Batch |
109916 | 20hp High Speed Disperser, Lift Mounted on floor w/48" Rise, 14" Blade (135-1350rpm) @ 8" off floor, SS-304, Shaft Guard, Limit Switches, Adj. Can Lock, XP Motor. (W-Cyl) | 2 WEEKS |
| RECON | HSD-20 High Speed Disperser Batch |
213644 | 20hp High Speed Disperser, Lift Mounted on floor w/48" Rise, 15" Blade (125-1250rpm) @ 11" off floor, SS-304, Shaft Guard, Limit Switches, Adj. Can Lock, TEFC Motor. Carbon Steel base with Fork Channel design for lifting (RD2224). | STOCK |
| RECON | HSD-25 High Speed Disperser Batch |
210071 | 25HP TEFC High Speed Disperser, Lift Mounted on floor w/54" Rise, 16" Blade @ 8" off floor, SS-304, Shaft Guard, Limit Switches, Adj. Can Lock, TEFC Motor. | 1-WEEK |
| NEW | PBA-2 Paddle Blade Agitator Gentle Agitator High Viscosity Disperser Bowtie Pitched Blade |
2HP TEFC, AIR/OIL, SS-304, 80-GRIT, TABLE MOUNT DESIGN, MOUNTED ON BENCH, 36-540RPM (6-90Hz), 6" 3-WING BOW-TIE BLADE (OTHER SIZES/TYPES AVAILABLE), 4" COLOR TOUCH SCREEN MOUNTED ON FRONT OF BONNET, NEMA-1 3/60/230V VFD MOUNTED INSIDE OF BONNET. | 3-4 WEEKS | |
| NEW | PBA-10 Paddle Blade Agitator Gentle Agitator High Viscosity Disperser Bowtie Pitched Blade |
10HP XP, AIR/OIL, SS-304, 80-GRIT, FLOOR MOUNT DESIGN, 44-175RPM, 18", 20", 22" 3-WING BOW-TIE BLADE, (OTHER SIZES/TYPES AVAILABLE). | 3-4 WEEKS | |
| RECON | PBA-2 Paddle Blade Agitator Gentle Agitator High Viscosity Disperser Bowtie Pitched Blade |
214530 | 2HP TEFC, AIR/OIL, SS-304, 80-GRIT, TABLE MOUNT DESIGN, MOUNTED ON BENCH, 36-540RPM (6-90Hz), 8" 3-WING BOW-TIE BLADE, NEMA-4X 3/60/230V VFD. | STOCK |
| RECON | PBA-5 Paddle Blade Agitator Gentle Agitator High Viscosity Disperser Bowtie Pitched Blade |
113173 | 5HP XP, AIR/OIL, SS-304, 80-GRIT, FLOOR MOUNT DESIGN, 9-88RPM, 20" DIA 3-WING BOW-TIE BLADE W/RISERS, DESIGNED FOR 55-GAL DRUM MIXING, CAN BE USED FOR OTHER SIZE VESSELS (OTHER SIZES/TYPES AVAILABLE). ADD VFD AND XP CONTROLS AS REQUIRED. | 1-WEEK |
Copyright 2017 Charles Ross & Son Company. All rights reserved.